Show simple item record

dc.contributor.authorReyes, Aase
dc.contributor.authorBørvik, Tore
dc.date.accessioned2019-09-13T13:05:39Z
dc.date.accessioned2019-09-27T09:00:19Z
dc.date.available2019-09-13T13:05:39Z
dc.date.available2019-09-27T09:00:19Z
dc.date.issued2019-05-09
dc.identifier.citationReyes A, Børvik T. Low velocity impact on crash components with steel skins and polymer foam cores. International Journal of Impact Engineering. 2019;132en
dc.identifier.issn0734-743X
dc.identifier.issn0734-743X
dc.identifier.issn1879-3509
dc.identifier.urihttps://hdl.handle.net/10642/7580
dc.description.abstractEnergy absorbing systems are extensively used in the automotive industry to ensure crashworthiness. Such crash components could typically consist of a sandwich structure with thin ductile plates as skins and a cellular foam as core to dissipate the kinetic energy. In a previous study, the quasi-static behaviour of two polymeric foam types with different densities, namely extruded polystyrene (XPS) and expanded polypropylene (EPP), used as core material in typical crash components was examined. The investigation involved a large number of compression tests of the core materials loaded in different material directions and indentation tests on sandwich structures in different configurations. In the present study, low-velocity impact tests are conducted in a drop tower on the same target configurations consisting of 0.8 mm thick skins of Docol 600DL steel and the various foams as core. During testing, the dropped mass was kept constant at approximately 15 kg, while the impact velocity varied between 5 and 10 m/s. The impact force was registered by the instrumented striker of the drop tower, and these measurements were used to obtain the displacement of the striker and the energy absorption of the different crash components. In addition, high-speed cameras and 3D-DIC were used to measure the out-of-plane displacement of the back skin. The presented results indicate that to minimise the weight and at the same time maximize the energy absorption of the crash component, a low density foam should be used as core material. It is also shown that by proper design, it is possible to optimize the protection level of such components, at least within a given velocity range.en
dc.description.sponsorshipThe present work has been carried out with financial support from Centre of Advanced Structural Analysis (CASA), Centre for Research-based Innovation, at the Norwegian University of Science and Technology (NTNU) and the Research Council of Norway through project no. 237885 (CASA).en
dc.language.isoenen
dc.publisherElsevieren
dc.relation.ispartofseriesInternational Journal of Impact Engineering;Volume 132, 103297
dc.rights© 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/en
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/
dc.subjectSandwich structuresen
dc.subjectMaterial testsen
dc.subjectEnergy absorptionen
dc.subjectImpact tests
dc.titleLow velocity impact on crash components with steel skins and polymer foam coresen
dc.typeJournal articleen
dc.typePeer revieweden
dc.date.updated2019-09-13T13:05:39Z
dc.description.versionacceptedVersionen
dc.identifier.doihttps://dx.doi.org/10.1016/j.ijimpeng.2019.05.011
dc.identifier.cristin1720767
dc.source.journalInternational Journal of Impact Engineering


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record

© 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/
Except where otherwise noted, this item's license is described as © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/